top of page
3D Matrix Booster

No compromise, an absolute surface innovation with assurance


3D Matrix Booster



Autotriz 3D Matrix Pro is an innovation with its unachievable levels of gloss, durability and chemical resistance. The active resin binds with complex polymers and Polysilazanes bond into surface pores, forming an extremely durable semi-permanent coating which cannot be washed off; resulting in a hard protective shield that preserves your paintwork.

Lembar Data Keselamatan


Most trustable protection in protecting your vehicle against the common elements that damage your vehicle’s paint.


Sand Dust

Sand dust causes scratches to the surfaces


Acid rain that will cause stubborn water spots on surfaces


Magnesium chlorid sprayed onto the roads during the winter season


Scratch Resistant

Tested to achieve above 9H hardness. Bonds on paint and lacquer as a barrier of protection to resist elements that will harm the car paint.


Absolute Weather Protection

Improve car maintenance as it offers a better surface that is suitable for any harsh weather conditions such as snow, rain, and extreme sunlight.

Extreme Gloss and Color Depth

Ground-breaking innovation of paint protection coating with an incomparable level of gloss, durability, and resistance that enhances surface reflections and shininess.

All Time Protection

An absolute layer of protection that is suitable for all roads. Stops the deterioration of car paint while repelling road contaminants such as tar that was splashed onto the surface of the car while driving.


UV Proteciton.png

Chemical resistance

Coating withstands strong chemicals and strong detergents.

UV Proteciton.png


Reduce surface friction and prevent the build-up of dust/dirt.

UV Proteciton.png


Improves cleaning experience as dirt can be washed off easily.

UV Proteciton.png

High durability

The excellent protection does not deteriorate easily.

UV Proteciton.png

UV protection

Preserves valuable surfaces against aging and discoloration.

UV Proteciton.png


Protect against the build-up of surface rust caused by road salt.

Petunjuk Penggunaan

Shake well before use.

Get ready with 3 pieces of a brand-new, lint-free microfiber towel. (It is recommended that new towels be rinsed or washed with water prior to use to reduce the loosing lint)

When first applying AUTOTRIZ 3D Matrix Pro Coating on the substrate, it is recommended to condition the surface of the applicator block with 7-8 drops to prevent skipping or dry spots.

It is recommended to do a 2 ft. x 4 ft. area or 4 ft. x 4 ft. at a time.

Apply AUTOTRIZ 3D Matrix Pro Coating using normal pressure on the applicator. Make sure the area is well covered. Always start from an edge to avoid excess on other panels. Work in controlled areas to remember where you previously applied. Work in horizontal or vertical movements repeatedly to ensure that product is penetrated through a clear coat.

Wait for 5-10minutes (time is varied from different countries and different seasons depending on temperature or humidity, ask distributors for a recommendation), and use the first towel to level the product.

Go immediately over with a second microfiber towel with a polishing motion until the surface is free from residue.

Follow by the third towel (this is called the “insurance towel”) and go over the surface one extra time just to make sure you haven’t missed any streaks or excess residue.

When the whole car is applied, allow curing of the coating to begin. Wait approximately 30-60 minutes before applying a second layer. Curing times depend on temperature and humidity. Applying the product too early will dissolve the previous layer.


Tertarik untuk menjadi seorang


Jika Anda tertarik dengan produk kami atau ingin bekerja sama dengan kami, kirimkan pesan kepada kami dan kami akan menghubungi Anda untuk menjadwalkan panggilan cepat atau hubungi kami melalui email kami

Setelah informasi ini diterima, tim kami akan meninjau akun dan menghubungi Anda.

Terima kasih telah mengirimkan!

bottom of page