PRODUCT

DATA SHEET

NANO

SERUM

PART #: AT-NS-50

DESCRIPTION

Nano Serum is the latest breakthrough in nano ceramic technology. It incorporates its nano-scale ceramic particles; acting as active agent to penetrate and fill up microscopic pores of clear coat.

 

Thus delivering the strongest covalent bond between 3D Matrix Coating and clear coat. It forms an ultra barrier against harmful environmental elements. Nano Serum sets a new industry’s standard of ultra-smooth and super hydrophobic coating.

PROPERTIES

- Permanent bond 

- >9H pencil hardness
- Excellent protection against graffiti / stains
- Easy-to-Clean
- Excellent adhesion to painted surfaces
- Outstanding weather resistance 
- High UV and chemical resistance 
- Easy to apply
- Cures at room temperature 
- Superior to Siloxane based coating

APPLICATION

Nano Serum is particularly suitable after V1 Top is applied to increase coating density.

TOOLS

Nano Serum can be applied with microfiber puff applicators.

TECHNICAL DATA 

Appearance: Colourless

Density: ca. 1,20 g/cm3

Base: Hydrofluoroether

Curing: Normal ambient temperature/ 80° celcius

Shelf Life: 12 months

Container Size: 50ml

INSTRUCTIONS FOR USE

The product is for professional use and should be applied by approved applicators only. Test on a small area or apply a test coat before application.

APPLICATION OF Nano Serum

 

Shake well before use.

 

Get ready with 1 pieces of brand new, lint-free microfiber towel. (It is recommended that new towels to be rinsed or washed with water prior to use to reduce the loosing lint)

 

When first applying Nano Serum on substrate, it is recommended to condition the surface of the puff applicator block with 7-8 drops to prevent skipping or dry spots.

 

It is recommended to do a 2 ft. x 2 ft. area or 4 ft. x 4 ft. at a time.

 

Apply Nano Serum using normal pressure on puff applicator. Make sure the area is well covered. Always start from an edge to avoid excess on other panels. Work in controlled areas to remember where you previously applied. Work in horizontal or vertical movements repeatedly in fast movements to ensure that product is penetrated.

Evaporation of Nano Serum is instant while you are applying. It is normal to see very little residue left on the surface.

When a full panel is applied, use microfiber towel with light polishing motion until the surface is clean and clear.

 

When the whole car is applied, allow curing of coating to begin. Curing times depend on temperature and humidity.

INFRA-RED CURING


Heating polysilazanes results in crosslinking to form higher molecular weight polymers. Curing can be accelerated by using IR Lamps. Recommended settings for IR lamps are as following:
i. Minimum 80cm of distance above the surface.
ii. Maximum 70⁰C of surface temperature.
iii. Maximum 30 minutes on each panel.

INSTRUCTIONS VIDEO

PROCESSING & CURING

Product must be applied at an ambient temperature of at least + 5°C and a relative humidity of 30 % - 80 %. Avoid direct sunlight! Apply the coating in dry conditions. Any mistakes can be rectified within approx. 10 min of application. Traces of water in the applicator should also be avoided. Applicators dampened with water should not be used. The applicators cannot be reused once the coating has been applied. Nano Serum is dry-to-touch after about one hour.

 

The recommended curing conditions (until water resistant) are:

- Room temperature: 8 – 12 hours

- 80 °C (Infra-red curing): 2 hours

Curing can be accelerated by using IR Lamps after V1 Top is applied. Heating Polysilazanes results in crosslinking to form higher molecular weight polymers. Recommended settings for IR lamps are as following:

i. Minimum 80cm of distance above the surface.

ii. Maximum 80⁰C of surface temperature.

iii. Maximum 30 minutes on each panel.

 

The 3D Matrix Coating plus Nano Serum is fully effective after 5 – 7 days’ curing at room temperature. During this time, the vehicles should not be driven into a vehicle wash.

© 2019 AUTOTRIZ

All rights reserved.

Customer Support

Phone No: +6011 5626 3898